Adaptec FS4500 - Hard Drive Array Guida Utente Scaricare il pdf (Pagina 22)

Home
Adaptec
Rastrelliere
FS4500 - Hard Drive Array
Guida Utente

Scaricare
Condividere

Condivisione
Aggiungi ai miei manuali
Stampa

2-4

Installing the Storage Enclosure

Installing into a Rack

Begin the installation by ensuring that you have all these rail kit

components:

■ Front rails (1 left, 1 right)

■ Rear rails, two different sizes (2 left, 2 right)

■ Two sizes of screws (10 large, 4 small)

■ Two types of nuts (10 of each)

To install your Storage Enclosure in a rack:

1 Secure the front rails to the front supports of the rack, using the

supplied screws, as shown in Figure 2-1.

Note: Use either the speednuts or cagenuts provided if

your rack does not have threaded holes.

Figure 2-1 Securing the Rails to the Rack

2 Check the length between the front and rear supports of your

equipment rack and determine which set of rear rails to use, the

long or the short.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 90 91

2U STORAGE ENCLOSURE 1
Copyright 2
Trademarks 2
Disclaimer 2
Adaptec Customer Support 3
Canadian Compliance Statement 8
Contents 10
8 Technical Specifications 11
Introduction 14
About This Guide 15
Kit Contents 16
Drive Slot Numbers 18
Installing the Storage 19
Enclosure 19
Installation Checklist 20
Installing into a Rack 22
One screw per side 24
Connecting SATA Cables 28
Connecting FC Cables 29
HOST BUS ADAPTER 30
SC4100 SCSI I/O Module 30
Modules 31
Next Steps 31
Monitoring 32
About the ES Module 33
Silencing the Audible Alarm 33
Understanding the LEDs 34
Drive Carrier LEDs 35
APC Module LEDs 36
Removing and Replacing 38
Enclosure Components 38
Hot-swapping Drive Carriers 39
Hot-swapping an APC Module 41
Removing an APC 42
Installing an APC 43
Replacing an I/O Module 44
Chapter 5 46
Chapter 7 46
Hot-swapping the ES Module 47
SATA Storage Enclosures 48
(FS4100 and FS4500) 48
Disk Drive Spin-up Sequence 49
I/O Modules 49
SATA Configurations 50
Dual SATA Configurations 51
Flexibility and Limitations 51
Enclosures 52
SATA I/O Module LEDs 53
SATA I/O Module Configuration 55
Fibre Channel Storage 56
Enclosures (FC4100) 56
Fibre Channel Cables 58
Fibre Channel ID Assignment 60
Disk Drive ID Map 60
121110987 61
2 Gb/sec Operation 62
LIO Module LEDs 62
Storage Enclosure LEDs 63
Ultra320 SCSI Storage 64
Cables and Termination 66
Split-bus SCSI IDs 67
Joined-bus SCSI IDs 68
Configuring Joined-Bus 69
Technical Specifications 70
General Specifications 71
Temperature 72
Humidity 72
Specifications 74
I/O Module Configurations 76
Cable Lengths Supported 76
Serial ATA Interface 77
SATA I/O Modules 77
SATA Cables 77
Disk Drives 78
Configuring the RAID 79
Controller (FS4500 only) 79
Communication Parameters 80
Initial Screen 80
Creating a Logical Drive 81
Quick Installation Option 82
View and Edit Host LUNs 84
Revision number 85
Serial number 85
Disk capacity (blocks) 85
Disk reserved space 85
System Functions Option 89
Adaptec, Inc 91
691 South Milpitas Boulevard 91
Milpitas, CA 95035 USA 91

Commenti su questo manuale

Nessun commento

Adaptec FS4500 - Hard Drive Array Guida Utente Pagina 22

Commenti su questo manuale