Adaptec ARO-1130SA Manuale delle Istruzioni Pagina 1

RInstallation and Hardware GuideARO-1130SARAID Option Cardfor PC Serverswith RAIDport I or II

1-11▼ ▼ ▼ ▼IntroductionThe Adaptec® ARO™-1130SA RAID Option card provides powerful disk array support in servers that have an available PCI/RAIDpor

1-2ARO-1130SA Installation and Hardware GuideSystem RequirementsThe minimum system requirements for the ARO-1130SA are An IBM PC (or compatible) serve

1-3IntroductionInstallation OverviewTo install ARO-1130SA hardware and software, follow these steps:1Locate the PCI /RAIDport I or II expansion slot o

2-12▼ ▼ ▼ ▼Installing ARO-1130SA HardwareThis chapter explains how to install the ARO-1130SA. To install the ARO-1130SA, you must Verify presence o

2-2ARO-1130SA Installation and Hardware GuideARO-1130SA LayoutFigure 2-1 identifies the major ARO-1130SA components. You may find it helpful to refer

2-3Installing ARO-1130SA HardwareVerifying Presence of DIMM MemoryBefore you can use the ARO-1130SA, the DIMM memory socket must be populated with a D

2-4ARO-1130SA Installation and Hardware GuideInstalling the ARO-1130SAFollow these steps to install the ARO-1130SA:Note: Before installing the ARO-113

2-5Installing ARO-1130SA HardwareConnecting the LED Cable to the ARO-1130SA(Optional feature) An LED on the front panel of most computers lights to in

Adaptec, Inc.691 South Milpitas BoulevardMilpitas, CA 95035© 1998 Adaptec, Inc.All rights reserved. Adaptec, and the Adaptec logo are trade-marks of

2-6ARO-1130SA Installation and Hardware GuideCompleting the InstallationOnce the ARO-1130SA is installed in your server, refer to the docu-mentation t

3-13▼ ▼ ▼ ▼Using the Array1000xA BIOS & Driver Selection UtilityWhenever you install a new ARO-1130SA in your server and before you run the Ada

3-2ARO-1130SA Installation and Hardware GuideRunning the Array1000xA BIOS & Driver Selection UtilityThe Array1000xA BIOS & Driver Selection Ut

3-3Using the Array1000xA BIOS & Driver Selection Utility– Save Current BIOS to a File. Saves the current ARO-1130SA BIOS to a file.– Erase Current

4-14▼ ▼ ▼ ▼Creating the First Array With the ArrayConfigSA UtilityThis chapter explains how to use the ArrayConfigSA Utility to create the first bo

4-2ARO-1130SA Installation and Hardware GuideCreating an ArrayFollow these instructions to create the first array with ArrayConfigSA:1Insert the Array

4-3Creating the First Array With the ArrayConfigSA Utility6Select the number of drives you want in the array and press Enter. This number should not i

4-4ARO-1130SA Installation and Hardware Guide8Select spares. If you do not want a spare, type n and continue with Step 10. If you want to select dedic

4-5Creating the First Array With the ArrayConfigSA UtilityMaking the Array BootableYou can make the array bootable so that the server boots from the a

R▼ ▼ ▼ ▼ ARO-1130SARAID Option Cardfor PC Serverswith RAIDport I or IIInstallation and Hardware Guide

4-6ARO-1130SA Installation and Hardware GuideNote: You cannot use this procedure to change the boot order of a SCSI disk drive that is not part of an

5-15▼ ▼ ▼ ▼Installing Software on a Windows NT ServerThis chapter explains how to install the software required to use the ARO-1130SA in a system u

5-2ARO-1130SA Installation and Hardware GuideInstalling the Array1000xA Driver for Windows NTThis section explains how to install the Adaptec Array100

5-3Installing Software on a Windows NT ServerNote: To install Windows NT from a bootable CD-ROM, make sure BIOS Support for Bootable CD-ROM is enabled

5-4ARO-1130SA Installation and Hardware GuideInstalling the Driver When Windows NT is Already InstalledTo update or install the cda1000.sys driver if

5-5Installing Software on a Windows NT ServerInstalling Adaptec CI/O Management Software for Windows NT ServerNote: The Adaptec CI/O Management Softwa

5-6ARO-1130SA Installation and Hardware GuideNote: These NT Services are configured to start auto-matically at boot time. After installation you can s

6-16▼ ▼ ▼ ▼Installing Software on a Novell NetWare ServerThis chapter explains how to install the software required to use the ARO-1130SA in a Nove

6-2ARO-1130SA Installation and Hardware GuideInstalling the Array1000SA Driver for Novell NetWareThis section explains how to install the Adaptec Arra

6-3Installing Software on a Novell NetWare Server4Insert the appropriate Adaptec Array1000xA Family Manager Set driver diskette (Disk A or Disk B) int

iiCopyright© 1998 Adaptec, Inc. All rights reserved. No part of this publication may be repro-duced, stored in a retrieval system, or transmitted in a

6-4ARO-1130SA Installation and Hardware GuideNote: To load the driver automatically at server bootup, make sure the startup.ncf file includes the load

6-5Installing Software on a Novell NetWare Server3Load the NetWare install program from the NetWare colon prompt (:load install). Follow the instructi

6-6ARO-1130SA Installation and Hardware GuideInstalling the TIRPC Communications ModuleThe TIRPC communications module must be installed before you in

6-7Installing Software on a Novell NetWare Server7Select NetWare 4.0 TIRPC Runtime and Configuration Files. (TIRPC must be installed in the sys:system

6-8ARO-1130SA Installation and Hardware Guide3From the NWSETUP Installation menu, select Default Installation or Custom Installation (press F1 for hel

7-17▼ ▼ ▼ ▼Installing Software on a Remote ClientThis chapter explains how to install the Adaptec CI/O Management Software on a remote network clie

7-2ARO-1130SA Installation and Hardware GuideInstalling Adaptec CI/O Management SoftwareFollow these steps to install the software:Note: Before you st

7-3Installing Software on a Remote ClientNote: You must have the proper level of Adaptec CI/O Management Software password authorization if you want t

A-1A▼ ▼ ▼ ▼Configuring ARO-1130SA with the SCSISelect UtilityThe SCSISelect configuration utility allows you to change SCSI set-tings without openi

iiiFederal Communications Commission Radio Frequency Interference StatementWARNING: Changes or modifications to this unit not expressly approved by th

A-2ARO-1130SA Installation and Hardware GuideStarting the SCSISelect UtilityTo start SCSISelect, press Ctrl-A when the following prompt appears when y

A-3Configuring ARO-1130SA with the SCSISelect UtilityExiting SCSISelectTo exit SCSISelect, press Esc until a message prompts you to exit (if you chang

A-4ARO-1130SA Installation and Hardware GuideSCSISelect SettingsSCSI Bus Interface DefinitionsThe following settings are the SCSISelect settings most

A-5Configuring ARO-1130SA with the SCSISelect UtilitySCSI Device ConfigurationThe SCSI device settings allow you to configure certain parameters for e

A-6ARO-1130SA Installation and Hardware GuideAdditional OptionsArray1000xA BIOSThis option determines whether the ARO-1130SA BIOS is installed at boot

B-1B▼ ▼ ▼ ▼Using the ARO-1130SA with Other Adaptec ProductsYou cannot install more than one ARO-1130SA card in the same system; however, you can in

B-2ARO-1130SA Installation and Hardware GuideUsing Driver Disk BIf the Array1000xA BIOS & Driver Selection Utility determines you require Disk A o

B-3Using the ARO-1130SA with Other Adaptec ProductsScenario #1: Adding an ARO-1130SA to a RAIDport I or II System with an AHA-294x, AHA-3940, or Other

B-4ARO-1130SA Installation and Hardware Guide3When the Registry Editor window appears, expand the tree on the left until you can see the nodes under \

B-5Using the ARO-1130SA with Other Adaptec Products01 01 00 00etc.You need to write down all the number groups from all rows in the table.cIn each gro

B-6ARO-1130SA Installation and Hardware Guide16Exit from the Registry Editor and from Windows NT. Then shut down the server.17Physically install the A

B-7Using the ARO-1130SA with Other Adaptec ProductsChanging Registry Settings1Back up the NT Registry, using one of the techniques described in Backin

B-8ARO-1130SA Installation and Hardware Guide8Click the right mouse button on SCSI Miniport on the right side of the window and select Modify from the

B-9Using the ARO-1130SA with Other Adaptec ProductsdWrite down the series of resulting numbers, without all the extra zeroes. In this example, it is 2

B-10ARO-1130SA Installation and Hardware GuideBacking up the Windows NT RegistryIt is very important to back up the Windows NT Registry before making

C-1C▼ ▼ ▼ ▼TroubleshootingTroubleshooting ChecklistCheck the following if you have problems installing or running the ARO-1130SA and SCSI devices:

C-2ARO-1130SA Installation and Hardware GuideProblems Running the Software On Your Windows NT ServerIf the Adaptec CI/O Management Software does not s

C-3Troubleshooting– The correct entries for HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\EventLog\System\CIOArrayManagement are:EventMessageFi

C-4ARO-1130SA Installation and Hardware Guide– The correct entries for HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\CIOArrayManager RPC Event

C-5Troubleshooting–Make sure HKEY_LOCAL_MACHINE\SOFT-WARE\Adpatec\CIOSNMP\CurrentVersion includes a value like this:Pathname: REG_SZ: [installationpat

v▼ ▼ ▼ ▼ Contents1 IntroductionSystem Requirements 1-2Installation Overview 1-32 Installing ARO-1130SA HardwareARO-1130SA Layout 2-2Verifying Pr

D-1D▼ ▼ ▼ ▼Using a CD-ROM DriveShould you need to install a CD-ROM, the Array1000xA Family Manager Set drivers diskette included with the ARO-1130S

D-2ARO-1130SA Installation and Hardware GuideTo complete the driver installation, edit the config.sys file to include command lines for aspi8dos.sys a

D-3Using a CD-ROM DriveCommand Line Options for aspi8dos.sysOption Example Use/ccbs<count>/ccbs8 Specifies the maximum number of concurrent ASPI

D-4ARO-1130SA Installation and Hardware GuideCommand Line Options for aspicd.sysOption Example Use/d:<name>/d:aspicd0 Required in the config.sys

D-5Using a CD-ROM DriveUsing a CD-ROM Drive with NetWareTo operate a CD-ROM drive connected to the ARO-1130SA under NetWare, you need the aspicd.dsk d

E-1E▼ ▼ ▼ ▼Using the SNMP AgentThis appendix provides information on using the SNMP agent for NetWare and Windows NT. A section describing how to l

E-2ARO-1130SA Installation and Hardware Guide2Similar to instructions for the Protocol IPX section, edit the traptarg.cfg file to specify IP addresses

E-3Using the SNMP AgentLoading MIBs in the MIB DatabaseFollow the procedure below to load MIBs in the MIB database while running HP OpenView. For more

viARO-1130SA Installation and Hardware Guide6 Installing Software on a Novell NetWare ServerInstalling the Array1000SA Driver for Novell NetWare 6-2In

Index-1▼ ▼ ▼ ▼ IndexAAAA-130xx Series adapters B-1Adaptec CI/O management software 1-3, 5-5, 6-1, 6-7, 6-8, 7-2AHA-2940 familydriver B-6ARO-1130

ARO-1130SA Installation and Hardware GuideIndex-2Disconnection A-1, A-5DLLs 7-3Driversfor DOS D-1for NetWare 6-2, D-5for Windows NT 5-2EEnable disconn

Index-3IndexRAID 0/1 4-2RAID 1 4-2RAID 5 4-2Registry B-3Remote client 7-1, 7-2Requirements, system 1-2RPCSTART 6-8SSCSIcables C-1channels 2-5ID number

viiContentsB Using the ARO-1130SA with Other Adaptec ProductsUsing Driver Disk B B-2Using the ARO-1130SA with an AHA-294x, AHA-3940, or Other AIC-78x0